Welcome to the Quality Gate for the Shoreham!
start
 
What is the Job Number? *

XXXXX-XX
 
What Quality Gate are you inspecting? *


 
Who is performing this inspection? *











 
Who performed the work? *









 
Who is performing this inspection? *



 
Who performed the work? *









 
Who is performing the inspection?







 
Is the job cut out of the correct material for required finish? (Use finish chart)

     
 
Incorrect material. Please do not proceed until you have the correct finish for work order.

 
How many fixtures are in this order? *

 
Do you have ({{answer_9426106}} x 1) of the DC-2900HR-P1? *

     
 
Incorrect amount. Please do not proceed until you have the exact amount of parts requested on work order.

 
Do you have ({{answer_9426106}} x 1) of the DC-2900HR-P3? *

     
 
Incorrect amount. Please do not proceed until you have the exact amount of parts requested on work order.

 
Do you have ({{answer_9426106}} x 2) of the DC-2900HR-P14? *

     
 
Incorrect amount. Please do not proceed until you have the exact amount of parts requested on work order.

 
Does door fit and function correctly?

 
Is this fixture square on all sides and corners? *

     
 
Is the door centered on the cage? *

     
 
Do the pins insert freely and the door operate as intended? *

     
 
Do the barrel hinges match the top of the door? *

     
 
How many glass tabs do you have? *

 
Incorrect. You should have 12 of these parts.

 
Are all (12) glass tabs securely soldered and in the correct location? *

     
 
Have the (2) 8-32 holes been drilled and tapped properly for the set screws? *

     
 
Do the solder seams meet the UECo standards? *

     
 
Do you have all loose parts/hardware required to move to the next step?

Count the parts and then answers questions below:
 
How many ARM-BENT-2x2 do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many CHK-TAP-7/8 do you have? *

 
Incorrect. You should have 4 of these parts.

 
How many PRT-UE-8710WR-P13-STL do you have? *

 
Incorrect. You should have 1 of these parts.

 
How many CNDL-SLV-7/8 x 4-NO-NCH do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many NUT-LK-10-098 do you have? *

 
Incorrect. You should have 4 of these parts.

 
How many NUT-LK-10-909 do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many FST-8-32-x1/2-SSSS do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many NIP-2-1/8P do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many CPL-PLN-10-126 do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many FST#14 1 1/2 RHPH-SMS do you have?

 
Incorrect. You should have 4 of these parts.

 
If necessary, please fill out an INC before moving the fixture to Surface Prep.

 
Congratulations on completing the Craft Quality Gate!

 
Is the fixture free of excessive solder, visible solder holes, and still meet UECo standards for solder seams? *

     
 
Does the door still fit properly in the hinges, close flat to surface, and fit with the door pin? *

     
 
Are all (12) glass tabs still securely soldered and present in all locations? *

     
 
Do you have all loose parts/hardware required to move to the next step?

Count the parts and then answers questions below:
 
How many ARM-BENT-2x2 do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many CHK-TAP-7/8 do you have? *

 
Incorrect. You should have 4 of these parts.

 
How many PRT-UE-8710WR-P13-STL do you have? *

 
Incorrect. You should have 1 of these parts.

 
How many CNDL-SLV-7/8x4-NO-NCH do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many NUT-LK-10-098 do you have? *

 
Incorrect. You should have 4 of these parts.

 
How many NUT-LK-10-909 do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many FST-8-32x1/2-SSSS do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many NIP-2-1/8P do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many CPL-PLN-10-126 do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many FST#14 1 1/2 RHPH-SMS do you have?

 
Incorrect. You should have 4 of these parts.

 
If necessary, please fill out an INC before moving the fixture to Finishing.

 
Congratulations on completing the Surface Prep Quality Gate!

 
Does the fixture finish match the work order? *

     
 
Is the finish free of any visible defects in the finish (i.e. scratches, spots, inconsistent coverage)? *

     
 
Does the door still fit properly in the hinges, close flat to surface, and fit with the door pin? *

     
 
Do you have all loose parts/hardware required to move to the next step?

Count the parts and then answers questions below:
 
How many ARM-BENT-2x2 do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many CHK-TAP-7/8 do you have? *

 
Incorrect. You should have 4 of these parts.

 
How many PRT-UE-8710WR-P13-STL do you have? *

 
Incorrect. You should have 1 of these parts.

 
How many CNDL-SLV-7/8x4-NO-NCH do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many NUT-LK-10-098 do you have? *

 
Incorrect. You should have 4 of these parts.

 
How many NUT-LK-10-909 do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many FST-8-32x1/2-SSSS do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many NIP-2-1/8P do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many CPL-PLN-10-126 do you have? *

 
Incorrect. You should have 2 of these parts.

 
How many FST#14 1 1/2 RHPH-SMS do you have?

 
Incorrect. You should have 4 of these parts.

 
If necessary, please fill out an INC before moving the fixture to GWP.

 
Congratulations on completing the Finishing Quality Gate!

 
Is the fixture and hardware free of any finish defects? *

     
 
Was the glass cut properly and does it fit securely in the tabs? *

     
 
Are the cluster arms and candle sleeves the correct dimensions and vertically aligned with the fixture in all directions? *

     
 
Has the ground screw been added to the mounting plate that is attached to back of the fixture? *

     
 
Did the fixture pass all Hi-Pot, Ground Continuity, and light bulb testing? *

     
 
Are all loose parts/hardware packed with the fixture?

 
(2) 25W T6 Tubular Bulbs *

     
 
(4) #14 x 1-1/2" Pan Head Screws *

     
 
(4) #14-16 Wall Anchors *

     
 
(2) Blue Wire Nuts *

     
 
Was the fixture packed per the Final Work Instructions? *

     
 
If necessary, please fill out an INC before clocking out the fixture.

 
Congratulations on completing the GWP Quality Gate!

Thank you, {{answer_9426027}}!
again
Thank you, {{answer_9426027}}!
again